JJS
Poor product and service.
I trusted AutoLEDTech to deliver a high-quality product but, unfortunately, received a subpar experience. I ordered custom-built headlights for over $2,000 and waited 10 weeks for their completion. Throughout this time, I found their communication severely lacking. Unlike other companies that keep customers updated on their orders, I had to reach out six weeks into the process to inquire about the status. When I did, the customer service team responded in a manner that felt dismissive and unprofessional, making me feel like a burden for simply seeking an update on a substantial purchase. When the headlights finally arrived, I had them professionally installed at a custom upgrades shop due to the complexity of the installation. Unfortunately, the shop discovered that the "demon eyes" feature I had paid extra for was not functioning correctly. One headlight displayed only a single color (green), while only white worked in both headlights, despite numerous troubleshooting efforts by the shop. Additionally, I noticed the left low beam was aimed far too low. Attempts to adjust the beam with the vertical alignment screw revealed that it was already maxed out, leaving the beam dangerously short at about 50 feet—significantly lower than stock and unsafe for nighttime driving. While the headlights are custom-built, I discovered that instead of using high-quality SRT headlight housings, AutoLEDTech used cheap Chinese knock-offs. This explains the poor quality in both lighting and performance. To make matters worse, these subpar knock-offs were meant to replace my genuine SRT headlight housings, which were far superior in quality. For a product with such a high price tag, the use of inferior materials is both disappointing and unacceptable. When I reported these issues to AutoLEDTech, their immediate response was to blame the installation shop, claiming that the lights were improperly connected and the LEDs were damaged as a result—claims they said were not covered under warranty. However, the installation process for these headlights is entirely plug-and-play, with each connector only fitting into its specific location. It is impossible to connect them incorrectly. Despite this, AutoLEDTech refused to take responsibility for the malfunctioning components. Regarding the low-beam alignment issue, they suggested I adjust the screw, disregarding my explanation that it was already maxed out. I provided clear images comparing the output of my stock headlights to theirs, highlighting the drastic difference, but I received no constructive resolution. Even more frustrating, AutoLEDTech refused to acknowledge the issue with the substandard housings by simply ignoring my emails. I reached out multiple times to make them aware of the problems, but they failed to respond, effectively shutting down any attempt at resolution. Adding to the frustration, AutoLEDTech has no direct phone line, leaving email as the only mode of communication. This setup seems designed to limit customer service interaction, as my subsequent emails about these serious issues have gone unanswered. My experience with AutoLEDTech has been an extremely regretful mistake. Despite the high cost and extended wait time, I received a product that was not only defective but also unsafe for use. Coupled with poor customer service, a lack of accountability, the use of cheap knock-off components in place of genuine SRT housings, and their unwillingness to acknowledge or resolve these issues, buyers should beware of this company.
Response from autoledtech.comFeb 27, 2026
Hello, We take concerns involving fitment, lighting performance, and safety very seriously. Our custom headlights are built using specified housings and components based on the configuration selected at the time of order. We do not substitute components without disclosure. If there are concerns regarding housing quality or component specification, we require the headlights to be returned for inspection so we can properly evaluate the matter. With respect to the demon eye functionality described, these systems are controller-based and require proper configuration and wiring integrity to function correctly. If one side is not displaying properly, that is something we actively troubleshoot and resolve through testing or replacement where appropriate. Regarding beam alignment, vertical adjustment mechanisms are integrated into the housing itself. If an adjustment appears maxed out or non-functional, the unit must be physically inspected to determine whether the issue is mechanical, installation-related, or transport-related. We do not dismiss installation feedback, nor do we automatically attribute issues to installers. However, once wiring modifications, splicing, or troubleshooting steps are performed outside of our documented process, evaluation requires direct inspection. We categorically reject any suggestion that we knowingly use inferior components or operate without accountability. We have built and fulfilled thousands of custom lighting assemblies and stand behind our workmanship under our warranty terms. If you would like to proceed with a formal inspection, please contact [email protected] with your order number so we can initiate a structured return evaluation. – AutoLEDTech
